Top 10 How To Tap A Keg To A Kegerator Home Appliances Take the dust cover off of your keg and connect the keg coupler. twist the coupler clockwise into the keg until it's snug. lever handle couplers require you to pull the handle out before pushing it down or lifting it up. once the keg is tapped, you'll notice a little beer go into the line but it won't fill it until you open the faucet. This is a short video on how to tap a keg with a d system coupler for your kegerator! it also shows you how to set the pressure of your co2 tank and how to p.
How Does A Kegerator System Work вђ Keg Brew Supplies Insert the tap into the opening at the top of the keg. make sure the notches are lined up and push the tap in. do not lower the lever! : turn the tap clockwise until it locks while keeping the lever up. once the tap has seated properly, press down the levers to open the keg up. you tap a commercial style keg by using a keg coupler. Most kegs require a temperature of 36 40°f (2 4°c) for optimal serving. place the keg in a refrigerator or kegerator at least 24 hours prior to tapping to ensure it is nice and cold. remove the cap: locate the cap or seal on the top of the keg. use a wrench or a keg specific cap removal tool to carefully remove it. Turn off the gas supply to the keg. lift the coupler handle and turn the coupler counterclockwise to unlock and remove it. inspect the coupler to make sure all the seals washers are intact and in place. connect the coupler to the new keg and be sure to depress the coupler handle until it clicks into position. Locate the coupler on the keg (usually protected by a metal cap). remove the cap, slide the coupler onto the valve, and twist it until it locks securely in place. attach the hand pump on top of the coupler, press the tap firmly into the keg, and start pumping. the hand pump operates by pressurizing the keg with air, forcing the beer up and out.
How To Hook Up A Keg To A Kegerator Beverage Craft Turn off the gas supply to the keg. lift the coupler handle and turn the coupler counterclockwise to unlock and remove it. inspect the coupler to make sure all the seals washers are intact and in place. connect the coupler to the new keg and be sure to depress the coupler handle until it clicks into position. Locate the coupler on the keg (usually protected by a metal cap). remove the cap, slide the coupler onto the valve, and twist it until it locks securely in place. attach the hand pump on top of the coupler, press the tap firmly into the keg, and start pumping. the hand pump operates by pressurizing the keg with air, forcing the beer up and out. Follow these step by step instructions for assembling your kegerator and installing tapping a keg inside of it. 1. install caster wheels. before beginning, make sure the unit is empty – including the white metal keg floor (11). then, carefully tip the beer dispenser on its side. connect the casters (13) to the cabinet by screwing in each. Remove the dust cap from the keg and connect a coupler. to connect your coupler, twist it clockwise until it is locked. next, pull the handle out and push it down to ensure it is appropriately secured. place a co2 tank near the kegerator and connect a pressure gauge. place your keg inside the kegerator.
Get Your Party Started How To Tap A Keg Follow these step by step instructions for assembling your kegerator and installing tapping a keg inside of it. 1. install caster wheels. before beginning, make sure the unit is empty – including the white metal keg floor (11). then, carefully tip the beer dispenser on its side. connect the casters (13) to the cabinet by screwing in each. Remove the dust cap from the keg and connect a coupler. to connect your coupler, twist it clockwise until it is locked. next, pull the handle out and push it down to ensure it is appropriately secured. place a co2 tank near the kegerator and connect a pressure gauge. place your keg inside the kegerator.
Comments are closed.